Rock Sliders, 96-02 4Runner, Standard

0 item(s) in cart/Total: $0.00

Visit Yotatech Forums

Home > Sliders

Rock Sliders, 96-02 4Runner, with Kick Out

Part Number 96024RSK

Rock Sliders, 96-02 4Runner, with Kick Out

4Runner Rock Sliders with Kickout

Email a friend

Write a Review

Price

Your Price:

$249.00

Choose Options

Material Type

Quantity

Add to Gift Registry

Add to Wish List

Description

Rock Sliders are vital to protecting the rocker panels and doors of your 4Runner from damage from rocks and stumps.

Features:

68" Long for maximum protection of rocker panels near the tires.
4 legs per side for maximum strength. Legs are positioned near tires to provide strength and protection when driving off rocks.
Rear kick-out for diverting rocks around wheel. If you have Limited Edition flares, you may have to notch the rear flares for clearance.
Set at 20° angle.
Mounting Pads are flat and can be positioned higher on the frame for vehicles with body lifts (up to 2" body lifts).
Comes fully welded with legs, mounting flanges, and gussets. Ready to clamp on to your frame and weld on.
Made from 1 3/4" X .120 round HREW tubing. DOM tubing is available for additional fee.
Leg spacing is specifically designed for 96-02 4Runner frames.
Heavy duty design can take a pounding from the rocks while keeping body damage to a minimum.
Strong enough to take the entire weight of the truck.
A high-lift jack can be used anywhere along it's length for repositioning or repairs.
Sold in pairs.
Shipped unpainted.

Options:

DOM is available and is recommended if you intend to make a lot of contact with rocks or you wish to have extra strength.

These are "build to order" so please allow 1-3 weeks for fabrication.

Customer Reviews

View All Reviews

	Sliders
	Fit great, super burly. Makes it easier to get in and out of the truck plus they don't even flinch at a high lift jack.
	Reviewed by: Jesse Moore from Medford, OR. on 3/5/2012

	TRAIL BOUND
	THESE ROCKSLIDERS COULDN'T BE BETTER. THEY FIT AND LOOK GREAT. JUST PAINT AND WELD THEM ON. CANT WAIT TO GET THEM ON THE TRAILS. THANKS.
	Reviewed by: RICHARD SANCHEZ from BAKERSFIELD,CA.. on 12/15/2011

	Weekend Wheeler
	I've run somewhat generic Trail Gear sliders in the past, and these are far superior. Even a more expensive set of CBI sliders didn't fit the frame this good. Much better fit and finish, prep and paint and they are ready to weld on. Minor trimming with a Limited on the bottom edge of the flares, but its just plastic so no harm done. The only option I wish they had was powder coating as I live in the rust belt, and paint doesn't hold up quite as well.
	Reviewed by: Jeff Richtman from Minnesota. on 10/14/2011

	Great product
	Sliders were a breeze to install! They look great on my 4 runner. Heavy duty construction!
	Reviewed by: Charles from Colorado Springs Colorado. on 8/31/2011

	Finally
	High quality craftsmenship. Steel was in great condition. Wiped them down with denatured alcohol and were ready to paint. Welded right to the frame with no mods except to the rear fender flares. Plenty sturdy enough to use the highlift on them. Look great. Most people don't notice them which to me says they're actually designed for this vehicle as they don't stand out as awkward looking. Customer service was top-notch. I did A LOT of shopping around and I'm confident I made the best choice.
	Reviewed by: Michael Pallas from Fresno County. on 7/21/2011

Accessories

Shackle D-Ring, 3/4"

0 Review(s)

Your Price: $17.95

Mile Marker SEC8 12V winch 4.8 HP Series Wound Motor

0 Review(s)

~~Your Price: $518.00~~

On sale: $399.00